If administrators reduce the value for positive and negative phase corrections, administrators can reduce the threat that computers will receive time from invalid time samples for a Windows-based computer.
On the other hand, if administrators reduce the value, administrators may prevent computers from being ahead or behind the current time by more than the limits these values impose. If the registry entry values for positive and negative corrections are reduced, time will be increased or decreased. This value enables the computer to receive the time that is contained in any time sample, whatever inaccuracy.
This new default value is 48 hours. This hour value can be represented as either of the following values:. When you set the value to a value other than MAX 0xFFFFFFFF , you can prevent computers from adopting time that is very inaccurate in the scenarios where the computer is restarted or the connectivity to external time sources is disrupted. For example, consider the case in which you have the MaxPosPhaseCorrection and MaxNegPhaseCorrection registry entries set for 48 hours on all domain controllers in the forest.
If any single domain controller experiences an unusual time jump of more than 48 hours, the value that you set for the MaxPosPhaseCorrection and MaxNegPhaseCorrection registry entries will prevent other computers from making the same time jump. Therefore, computers that are out of sync can be kept apart from the other computers until the administrator can investigate and take corrective action.
Time accuracy is especially important on the forest root primary domain controller PDC. Because the PDC is the root time source for the domain, inaccurate time changes on the PDC can potentially cause a domain-wide time jump. If you impose phase correction restrictions on the PDC, you can prevent other domain controllers in the forest from accepting the new time.
The default value of 48 hours instead of a default value of 5 minutes or 15 minutes is based on the following reasons:. These errors have a low correlation to the time skew because the cause may prevent Windows-based computers from adopting an accurate time value. So 48 hours was the next obvious time offset after 25 or 36 hours. Administrators can also reduce the value with correct tools that report infrastructure and testing. Specific recommendations according to operating system version and computer role are described in the following sections.
When you configure the authoritative time server to sync with an Internet time source, there's no authentication. You must reconfigure the following registry entries:. This default value means "Accept any time change. It's represented in the registry as 2a hexadecimal or decimal. We recommend that you set the value of the MaxPollInterval registry entry to 10 or less or that you set the value of the SpecialPollInterval registry entry to 1 hour or less. The 48 hours value can also be set on member servers that are running time sensitive-based applications.
As a security best practice, we recommend that you reduce this default value. We also recommend that you set the value to 1 hour or an even smaller value, depending on time source, on network condition, on poll interval, and on security requirements. We recommend that you use the Global Policy object Editor to deploy these settings. The default Windows Time service parameter values that are defined in the Group Policy object GPO may not match the default values that are defined in the registry of Windows Server based domain controllers.
Other Windows Time service parameter values may also have to be changed in the GPO to match the default registry values in the domain controllers. When you configure the authoritative time server to sync with an Internet time source, there's no authentication in manual mode.
The default value is 43, The recommended value is 15 minutes or an even smaller value, depending on time source, on network conditions, and on security requirements. Figure 5: w32time behavior adjustment. Figure 6: Windows Date and Time synchronized successfully. Check if w32time service is running Note that w32time service may only be enabled when no other ntp daemon is installed on your system. Otherwise the two services come into conflict. Scroll to "Windows Time" feature and check its "Status", which should be on "running".
Check also the "Startup Type" and set it to "Automatic" or "Manual" if possible. If the status of the Windows Time is currently not shown, then right click and choose Properties to open "Windows Time Properties Local Computer " window. In the Service status click on the "Start" button to start the time service. The result should resemble Figure 7. Figure 7: w32time service settings. Select a reliable NTP server A great deal of synchronization problems may be caused by network break downs, unpredicted traffic delays, unknown accuracy and public NTP servers where you don't have control over.
Thank you. I went throgh this blog blogs. Clients are also affected by this problem. Did you create and apply all the group policys that that blog also shows as these are the ones that will automatically fix problems on every PC.
I just tested on my DC by changing the clock by a minute and using this command to set it back a to normal. You can change your pool servers according to geographic location if you prefer, but there's nothing stopping you from using the ones presented in my example they're in Canada. You need to restart the w32tm service before those changes will go into effect.
Also make sure the DC can get out to the internet, otherwise it will not be able to contact the time source. Also make sure the server can get out to the internet, otherwise it will not be able to contact the time source. When you use the update switch it's the same as restarting the service for the purposes of making changes. I replaced first of all the time server.
And then i replaced the battery in the physical server and it solved the problem. The problem was with the battery and i want to thank everyone of you for your time and help through this problem i was facing. Thanks a lot guys you are a great community here.
0コメント